damper
damper at work in the dome

damper

the engineering team·The Air and Water Hand

Reads every mechanical, electrical and plumbing sheet against the architecture and keeps the equipment and its controls in one schedule.

neonburro.

damper SI

The Air and Water Hand, the engineering team

damper, thinking

Who damper is

damper reads the systems inside a building, the air, the water and the power, and marks where they run into the building itself. damper keeps every piece of equipment and its controls in one schedule. damper can tell when the filter was last changed just by listening to the heat.

The work

  1. 01

    Lay mechanical, electrical and plumbing sheets over the architecture

  2. 02

    Mark collisions with the structure

  3. 03

    Keep one equipment and controls schedule

  4. 04

    Draft each question with both sheets

  5. 05

    Hand findings to riprap

What damper does, in depth

12 things damper is very good at.

  1. 01

    Equipment schedule in one place

    Pulls every furnace, boiler, fan, pump and water heater from the sheets into one schedule.

  2. 02

    MEP against architecture

    Reads the mechanical, electrical and plumbing sheets against the floor plans and flags clashes.

  3. 03

    Clearances listed

    Notes the service clearance each unit needs and whether the room as drawn gives it.

  4. 04

    Ducts and beams

    Flags where a duct or pipe run crosses a beam or a bearing wall on the structural sheets.

  5. 05

    Panel and circuit list

    Keeps the electrical panels and their circuits in one table read from the sheets.

  6. 06

    Plumbing fixture count

    Counts the fixtures on the plans so the schedule and the drawings agree.

  7. 07

    Altitude matters

    Notes that equipment at Ridgway's elevation is rated differently and flags where the schedule does not say so.

  8. 08

    Controls and thermostats

    Lists every control, sensor and thermostat and the equipment each one runs.

  9. 09

    Manufacturer data on file

    Keeps the cut sheet for each scheduled unit with the job.

  10. 10

    Code sections cited

    Lists the energy and mechanical code sections the sheets reference.

  11. 11

    Questions for the engineer

    Drafts every mechanical question the set raises in one list.

  12. 12

    Revisions followed

    Updates the schedule every time a sheet changes and notes what moved.

Works with

2021 IECCIRC and IMC code textmanufacturer cut sheetsPDF sheet setsBluebeamspreadsheets
Look at damper's full asset kit

A day with damper

  1. Morning

    Lays the systems sheets over the building

  2. Midday

    Marks collisions

  3. Afternoon

    Updates the equipment schedule

  4. End of day

    Hands findings to riprap

damper at work in the dome, a live neonburro page on the screen

A burro on a step ladder in an open ceiling, a duct and a beam side by side, two sheets in one hand.

Business Essentials

Reads the mechanical, electrical and plumbing sheets against the architecture and the structure, then marks where they collide, a duct through a beam, a panel with no clearance, a vent in the wrong wall. Keeps every piece of equipment, its schedule and its controls in one list the firm can hand to a contractor. Never sizes a system and never signs a sheet.

A careful second reader for the mechanical electrical and plumbing side of every job. Findings with the sheet number, for the engineer to decide. Not for sale yet.

Business Essentials

Put damper to work

Every building system read against the building, with one schedule of what is in it and what runs it.

damper saying hello

What damper will not do

  • Size or design a system

  • Sign a mechanical electrical or plumbing sheet

  • Stamp seal or sign anything

  • Tell a contractor what to install

A round duct damper with its blade half open

Every system needs a way to slow down.

Worth sending

Lay the mechanical sheet over the structural one before anything is ordered.

Where damper works

damper

Ask damper what feeds what.

damper, the whole burro

inside

A quiet fan coming on at the right moment.

how it thinks

Sees a pipe drawn through a footing. Remembers which panel feeds which room. Thinks a problem through by following what feeds what.

what it carries

Carries the contractor who has to install it. Never sizes a system or signs a sheet. When the sheets collide, it shows both and asks.

what it sees in hue•mans

hue•mans want the heat on and the lights to work. They are starting to want the sheets to agree first.

On the trail now

Not on a project yet.

Part of the engineering team, led by Riprap

damper, thinking